Android power chime manual#
Android power chime for android#
Android power chime android#
Android power chime code#
Android power chime password#

Android power chime code#

For iPhone/iPad tap on the symbol of a QR Code: Location of DID code on rear of aluminium case:

Android power chime android#

Enter the Default Security Code 123456 and click on save / okay / save this system.įor Android select “Scan DID Label”.( please see attached pictures for reference between the two)

Android power chime for android#

For Android click on “Scan DID Label” and for iPhone/iPad tap on the symbol of a QR Code. You can manually enter the 'DID' or use your smart device to scan the QR code.This is located on a QR code on the rear of the aluminium cover. The 'DID' is the Device ID of the DIC-23112 Doorbell.Enter a name of your choice for your DIC-23112.Tap on the to add a new system and a box will appear that you need to enter information into.Remember to ignore any message that says internet may not be available.

Android power chime password#

When prompted on joining the network enter the password 12345678 to connect / join.

A network with a name beginning HD-xxxxx will appear, please select this network as it is the independant WI-FI source of your doorbell.

On your smart device go to Wi-Fi settings and search for Wi-Fi networks.

Allow all permissions to the device, this will allow the application to fully function.

Download the 'Smartwares View App' from Google Play / Apple app store.

The DIC-23112 cannot connect to Wi-Fi that is not password protected.Ĭonnecting the DIC-23112 with your smart device Please have this ready to input when required.

The fourth password you'll be asked to enter is the password of your router.

You will be prompted to change this password to a password of your choice.

The default Admin Password 123456 is to access the Advanced Settings of the DIC-23112.

The default Security Code password 123456 is the security password for the DIC-23112 and you will be prompted to change this password to a password of your choice.

The first password 12345678 is the password for the Wi-Fi network of the DIC-23112 and you won't be asked to change this password.

In the next section “ Connecting the DIC-23112 with your smart device” you’ll be asked to enter 4 different passwords: Also during this time a green light will start blinking, this is to indicate that the deice is ready for set up with your smart device.

On the back of the device next to the power input there are two lights (see picture attached for reference) after 30+ seconds a red light will come on and stay steady.

First you must connect the power cable to a power supply, so plug it in and switch on.

Please do not put the rubber seal back in place yet.

Please ensure no bare cable is exposed, as it can cause an electrical short.

Connect the power cable to V+ and V- terminals (red cable to V+ and black to V-).

Push the power cable through the rubber seal and wire the power cable into the terminal block.

Slide the DIC-23112 back into the aluminium case, replace securing screws.

Firmly push the SD card cover back in place.

Open the SD card cover and insert SD card ensuring it’s fully inserted.

Slide the DIC-23112 out of aluminium case.Remove the rubber seal and 3 securing screws.Always ensure the device is completely powered off before inserting or removing an SD card.Only use the power supply provided with the DIC-23112.You can turn this back on after set-up is complete. For Android: If you’re using an Android smart device it might have Smart Switching enabled.In your smart device ensure the time setting is set to 24-hour format and not 12-hour format.Also the location where the DIC-23112 will be installed, ensure you have minimum 1Mb upload speed (The easiest way of doing so is using a internet speed test on a smart device such as Ookla,this it to be in the location while connected to your home network). When following the steps below please have the DIC-23112 within 5m of where your router is located.

Android power chime manual#

If you’re uncertain about this then please refer to the user manual of your router additionally you can contact your internet service provider.

The DIC-23112 doesn't support a 5GHz network band, therefore your Wi-Fi network must be on a 2.4GHz frequency during set up.

Please follow below for a comprehensive guide on set up of the DIC-23112 Wi-Fi Doorbell. Set-up guide for DIC-23112 Wi-Fi Doorbell Byron Door entry Wired doorbells & pushers DIC-23112 Wi-Fi Doorbell set-up guide